You have 2 options for adding or replacing tapes in an Ark Tape Library. You may use the mailslot to add or swap one or a few tapes without stopping the library or open a magazine to load or replace many tapes at once (this takes the library offline). This guide covers the EditShare Ark 24Q, 48Q, 40Q and 80Q Tape Libraries.
Which method to use
| Situation | Method | Library stays online? |
|---|---|---|
| Add, remove or swap 1 to a few tapes | Mailslot (Option A) | Yes |
| Initial load, or replace many tapes | Magazine (Option B) | No: changer motion stops while a magazine is out |
| Mailslot disabled, or partition has no mailslot | Magazine (Option B) | No |
OCP - Operator Control Panel (on LTO)
RMI - Remote Management Interface (Web UI)
| Model | Controls | Mailslots | How to open |
|---|---|---|---|
| 24Q | OCP buttons + RMI web page | 1 (front slot of left magazine) | OCP Commands menu or RMI Operations |
| 48Q | OCP buttons + RMI web page | 3 (left magazine) | OCP Commands menu or RMI Operations |
| 40Q | Magazine buttons, OCP, RMI | Right magazine, if enabled | Press the right magazine button |
| 80Q | Touch OCP + RMI | Per module, if enabled | OCP Home screen or RMI Operation menu |
Before you start
Every tape must have a single, correctly placed barcode label; neither the library nor EditShare Ark Tape supports unlabeled media.
- Right media for the drive. See Tape Compatibility with LTO Drives
- Barcode label. Use good-quality labels (self-printed labels often misread). Apply one label in the recessed area next to the write-protect switch, alphanumeric side toward the hub. Extra labels can jam a drive.
- Cleaning tapes. Label them with a barcode starting CLN so the library recognizes them for auto-clean.
- Write-protect switch. Slide left to allow writing; slide right to protect (a red mark or padlock shows).
- Handling. Don't drop, degauss or expose tapes to magnets or heat. If a tape was outside 10 to 35 °C, let it settle at room temperature for as long as it was exposed.
- Library idle. Check that no backup or restore job is running, especially before opening a magazine.
- Orientation. Insert each cartridge in the direction of the insertion arrow on the cartridge.
Option A: Add or replace a few tapes via the mailslot
The mailslot must be enabled first (24Q/48Q: RMU system configuration, Mailslot Enabled; 40Q/80Q: RMI Configuration > Mailslots). Enabling it turns those slots into import/export slots, so storage capacity drops by the same number.
To replace a tape, first move the old tape to the mailslot: use Move Medium (24Q/48Q OCP Commands menu, or RMU Operations > Move Media) / the move-media screen on the 40Q/80Q. Then open the mailslot as below, take the old tape out and put the new one in.
24Q / 48Q
- On the OCP, go to Main Menu > Commands > Open Mailslot and press Enter.
- Wait for Insert cartridge on the display. If it shows Busy, the changer is working; repeat the command when it finishes. Mailslot Disabled means the mailslot isn't enabled.
- Pull the mailslot out, remove any tape you are exporting, and insert the new tape in the direction of its insertion arrow.
- Push the mailslot back in until it seats. The library rescans the new tape.
40Q
- Check that the right magazine button LED is steady ON (mailslot enabled).
- Press the right button for less than 3 seconds. The LED flashes slowly while unlocking.
- When the LED flashes quickly and the OCP says the mailslot is unlocked, pull the mailslot out within 30 seconds (it relocks after that). It stays attached to the magazine.
- Swap or add the tapes, then push the mailslot back in. The library rescans automatically.
80Q
- On the OCP Home screen tap Open Mailslot (or in the RMI: Operation > Open Mailslot, click Unlock, then Submit).
- Within 30 seconds, open the magazine access door and pull the mailslot out.
- Swap or add the tapes and push the mailslot back in.
- Close the magazine access door.
Do not reach or insert tools into the library through the mailslot opening as there are moving parts inside.
Option B: Bulk load or replace tapes via a magazine
Opening a magazine takes the library offline (robot motion stops), so wait until no jobs are running. Magazine unlock may require the admin password or PIN, and you need about 60 cm (24 in) of clearance in front of the library.
24Q / 48Q
- Unlock the magazine: on the OCP go to Main Menu > Commands > Unlock Magazines and pick Left or Right, or in the RMU go to Operations > Release Magazines, choose the magazine and click Release.
- When the OCP shows Pull left (or right) magazine, pull the magazine straight out.
- Remove the tapes you are replacing and load the new ones into the empty slots.
- When the OCP shows Insert magazine, slide the magazine fully back in. It locks in place when seated.
- Repeat for any other magazine.
40Q
- Press the magazine's button for more than 3 seconds. The LED flashes slowly while unlocking.
- When the LED flashes quickly and the OCP confirms the unlock, pull the magazine out within 30 seconds. It does not eject by itself.
- Load or swap the tapes.
- Insert the magazine and push the handle slowly until the release latch snaps into place.
- Repeat for each other magazine.
80Q
- On the OCP or RMI, select the module, then Open Magazine (RMI: Operation > Open Magazine, click Unlock, then Submit). Only one magazine can be open at a time.
- Within 30 seconds, open the magazine access door and pull the magazine out.
- Load tapes from the back of the magazine forward, pushing the magazine back in as each bin fills.
- Push the handle slowly until the release latch snaps into place.
- Close the magazine access door, then repeat for other magazines.
If a magazine won't unlock from the OCP, RMU or RMI, use the emergency release described in your model's user guide which is available from your server's landing page.
After loading: verify and troubleshoot
Confirm the new tapes appear in the inventory before running jobs; rescan if they don't.
- Check inventory. 24Q/48Q: RMU Status > Tape Cartridge Inventory. 40Q/80Q: RMI Status > Cartridge Inventory. The 40Q/80Q rescans automatically after a magazine is closed.
- Rescan if needed. 24Q/48Q: OCP Commands > Reinventory, or RMU Operations (rescan media inventory) and click Rescan. 40Q/80Q: Operation > Rescan (RMI) or Operation > Inventory Scan (OCP). The library is busy until the scan finishes.
- Refresh the application. Let EditShare Ark Tape pick up the new barcodes before you assign the tapes to a media pool.
| Symptom | Fix |
|---|---|
| "!" next to a slot, Media Attention LED flashing | Tape is damaged, the wrong type or incompatible with the drive. Export it; the LED clears when all such tapes are out. |
| Wrong or missing barcode in inventory | Check the label is applied correctly, single and clean; replace it if needed. |
| Can't write to a new tape | Slide the write-protect switch to the write-enabled position. |
| Mailslot command shows Busy | Wait for the robot to finish, then repeat. |
| Magazine or mailslot relocked before you pulled it | You have 30 seconds after unlock (40Q/80Q); unlock again. |
| Magazine won't release | Use the emergency release in your model's user guide. |
Clean LED on? Load a CLN-labeled cleaning cartridge (with auto-clean on, the library uses it automatically). Clean only when the library asks.
For further information, please reach out to EditShare Support.
Comments
0 comments
Article is closed for comments.